In the United States Chop Service has established deep roots. However, in Europe it has yet to take off. Why?
What is it and how does it work?• | Less stock | |
The major advantage is that the framer is able to eliminate his stock or at least reduce it substantially. The framer simply displays the various corner samples without actually stocking the mouldings. This means that he leaves the customer with an embarrassing choice. It is a well known fact that a customer prefers to come into a shop that has a wide range. The American framer displays about 350 samples in his shop. There is no such reliable statistic in Europe but it can be safely stated that the average European framer stocks no more than half the average American amount. One of the most obvious consequences of reducing stock, is the reduction of capital that is tied up. Moulding inventory is a substantial item on a framer's balance sheet. An intermediate solution would be to keep a stock of the best sellers and use Chop for those mouldings seldom used, particularly the more expensive ones, that constitute a heavy investment of funds. Another advantage is the reduction of space. Chop avoids the useless and disorganised storage of many mouldings in the back room allowing greater functionality and leaving greater space to that part of the shop dedicated to display and customers. |
||
• | No more cut offs | |
Chop eliminates the problems associated with cut offs. Usually cut offs are piled up in a corner awaiting possible future use. Cut offs constitute a cost because they are paid at full price. Even if they were to be used to make smaller frames they could never cover the cost. They also take up space that could be used more effectively. By ordering the mouldings through Chop, the cut offs remain in the suppliers warehouse and the framer pays only for the mouldings supplied to him. |
||
• | No more defective mouldings | |
Another nagging inconvenience that can be overcome with Chop is eliminating crooked or defective mouldings. It is the supplier that is left with the responsibility and the cost of eliminating defective mouldings at the time of making the cut. This constitutes a reduction in cost for the framer. |
||
• | Identical mouldings | |
It must have happened to most framers to find themselves with four pieces of mouldings all nicely cut and ready for joining but unfortunately different in colour and/or finish. This often happens when mouldings are used from two different batches purchased at lengthy intervals. |
||
• | Try first and then buy | |
The advantages don't end here. There are others that a framer discovers as he acquires greater confidence with the whole system. A framer will realise that it is not necessary to purchase new models of mouldings. It is more conv enient to try them first with Chop. This way a framer can check them over and even evaluate customers' reactions. Only if the evaluation gives a positive result, will it be convenient to stock the mouldings. There will be a substantial reduction in the risk of purchasing the wrong moulding. |
||
• | A helping hand | |
Chop enables the framer to handle heavy work loads . There are times during the year when quiet periods alternate with not so quiet periods. Chop allows you to have a casual employee on-call. This helping hand allows the framer to level out these alternating periods. It is more comfortable to let your supplier do the work whilst you are busy. Chop comes in handy when personnel are sick or on holiday. Sometimes the owner himself is sick or away. Whenever the framer has to overcome an emergency the burden of employing extra staff is no longer required with Chop. Reliable, organised, on call and economically less onerous. That's Chop. |
||
• | For the beginner | |
If a framer was to exclusively use Chop there would be no need for any cutting equipment. This can be particularly handy for a framer starting out. In fact a framer could use Chop in the initial stages of his activity and only once his volume of work justified the investment would he purchase cutting equipment. Moulding cutting is an essential part of the framer's activity and the buying of a good quality saw should be evaluated closely. |
||
• | Those that are not framers | |
Photographers that are also framers, general shop owners, gift shops that sell small framed pictures and posters are all potential beneficiaries of Chop. Instead of purchasing expensive cutting equipment and keeping a stock of mouldings it is more logical and less problematic to have a large range of samples on display limiting the work to joining and assembling the frame. |
||
• | The inconveniences | |
Is it all nice and rosy? Not completely. There can be some disadvantages with Chop that discourage its use. First of all the price. The cost of a pre-cut moulding is greater than the moulding supplied as a mitre. The surcharge is usually around 80%. This is counterbalanced by all the other economical advantages such as no cut offs and no defects, no work, etc. There are inconveniences however with not keeping stock. The first is that when the supply of Chop doesn't arrive you are left stranded. Delays with the transport for example can occur. The supplier should be extremely rapid with delivery and needs to have a network of reliable and efficient transporters. You must insist that your supplier informs you as quickly as possible when they are out of stock of a particular moulding requested by you. This way you can let your customer know as soon as possible. If the moulding is damaged whilst handling or assembling it, the only option left is to re-order it with a consequent doubling of the expected completion times. What happens when the mouldings arrive damaged or with chipped off edges. Even though your supplier will most likely reimburse you, the expected completion time previously communicated to the client can no longer be met. It is important that you have suppliers that package the mouldings well. There is also an inconvenience with phone orders. Often mistakes can occur either in communicating the model or the dimensions. Model F-22 is often misunderstood as S-22 for example. A 45 x 40 cm frame is often misunderstood as a 55 x 40 one. If you telephonically order, then you should get the supplier to repeat the order back to you. Often there is a misunderstanding over the measurement system you use compared to that of your supplier. For example when you state 30 x 40 cm you probably mean 30.2 x 40.2 (you are already allowing for the application of glass, mountboard and backboard). You must be careful that what you believe is obvious may not be so for the supplier. Even though your supplier may deliver rapidly you will never be able to finish a job within a day or two. You will always have to allow for those few days for the preparation by the supplier and the subsequent delivery. You must assure that the samples you display must be current ones that the supplier continues to stock. You must have a supplier that rapidly communicates to you any changes in production. Mouldings follow fashions and manufacturers stop production of those mouldings that are no longer requested. Your sample display must constantly be kept up to date. In spite of a rather long list of disadvantages it has not discouraged American framers. From a recent survey it was found that 35% of American framers are very happy with Chop whilst 56% stated that they were reasonably happy. The two figures put together indicate that 91% of framers have a favourable opinion of Chop. |